Proscan tablet plt7777g-q stuck on android screen

#PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN INSTALL#
#PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN PASSWORD#

The screen flashes, and then the message, вЂњTouch the Future of ReadingвЂќ appears. Step 2 Press and hold the power button, and then press and hold the вЂњHomeвЂќ (вЂњn” key will still holding the power button down. Step 1 Press and hold the power button for 20 seconds to turn off the Nook tablet. Step 5 Confirm the action by tapping вЂњErase & Deregister Device.вЂќ All data is deleted from the tablet, and the device is restored to original factory settings. Step 4 Tap the вЂњErase & DeregisterвЂќ option to perform the factory reset. Step 3 Tap the вЂњDevice InfoвЂќ option to display the Factory Reset screen.

Step 2 Tap the вЂњSettingsвЂќ option in the Quick Navigation menu to open the Settings menu. Step 1 Press the вЂњHomeвЂќ (вЂњn') button to display the Quick Navigation menu on the Nook tablet. Note: If at any point during the above steps your tablet becomes unresponsive, you can restart it by holding down the power button for several seconds.

Scroll down to 'Yes - erase all user data' and press Power to select it.

Use the volume keys to scroll to 'wipe data/factory reset' and press Power to select it.

While holding down Power, press Volume Up.

You will see an image of an Android robot with a red exclamation mark.

Press Power to restart into Recovery mode.

Press Volume Down twice to designate Recovery mode.

You will see the word Start with an arrow drawn around it.

Press and hold Power until the device powers on, then immediately press and hold Volume Down (while still pressing Power).

#PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN PASSWORD#

If your tablet is password protected, you'll be prompted to enter your Pattern, PIN, or Password.

#PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN INSTALL#

Go through the new install process, adding your account/s & wifi details. The system should then Factory Reset as in the 'settings' process (method 1). Press the VOL DOWN button to select the 'Wipe Data' icon then VOL UP to confirm it.ДҐ. In JB there are four, the first of which is RCK.Д¤.

The right 'Android' will have a green highlight fading in and out. After a few seconds you should see some icons in the middle of the screen - in ICS they are called 'Wipe Data' and 'Android'.

If the TF booted the way it always does, you have not accomplished the task, try again until you have seen 2 icons (ICS), 4 icons (JB) in the screen.ДЈ. Press and hold the VOL DOWN and then POWER button at the same time for at least 10-12 seconds until after the start-up screen appears and is joined by some small print at the top of the screen, then let them both go. Unplug the power cord and shut the unit off.Дў. If you are unable to power off, try this process from point 2.ДЎ. Couldn't hurt, worth a try to avoid losing your stuff.ДЄSUS Transformer (most models are reset the same way) Most say to hold the Power button in for about 20 seconds or until the power menu appears (Power Off if you get the menu.), Then wait about a minute before powering on again. Just in case.)Д®dit: I've come across many recommendations to try a 'Soft' reset, before resorting to a 'Hard' reset such as the ones in this thread. (If your tablet has a MSD card, I'd recommend removing it as well. Note: Anyone using one of the procedures below should be aware that ALL personal data will be deleted from the tablet as part of the process. Any questions posted here may be deleted without notice by the Forum Staff. Questions belong in the forum for your tablet or, if there is no forum for your tablet, in the Q&A section. This is a thread for ANSWERS NOT QUESTIONS. You'll also have the appreciation of the Forum Staff. Your 'reward' for doing so will be the gratitude of anyone who uses it successfully and hopefully some clicks of the 'Thank' thingy in your post. Place the Make & Model of tablet on the first line to make searching easier. If you know of a procedure that works for a particular tablet (that the example in the second post does not work for), please post it in the same format as the second post for consistency. Hopefully, this will be a community effort and you'll participate if you can. This thread is intended to gather the many 'Factory Reset' replies scattered all over the forums into one location.

Proscan tablet plt7777g-q stuck on android screen